Automatic water softener. Electronic Autotrol valve 255/760 Logix 1″ (Reg. Metered-time). Valve body made of Noryl plastic material, NSF listed.
Programming is simple and fast, just enter the:
- time,
- day of week,
- time of regeneration, typically 02.00 at night,
- number of days between regenerations.
- hardness input.
Complete with plug adapter 12/230V – 50Hz European plug. Hardness regulator output.
Clutching the set screw is going to open the clapper by-pass, which allow you to mix raw water with water treated by device. At the first turn of the screw, the water hardness output increases. Is required output minimum hardness of around 15°F, but the most commonly used setting is not less than 5°F. Loosening setting screw will allow the clapper by-pass to close. The closing action will reduce mixing with raw water output. To mix a specific output hardness value, adjust screw and test water. Repeat the procedure until you reach the desired hardness value.
Regeneration type
– Electronic lap;
– Electronic volume;
– Programmable electronic chronometric;
– Programmable electronic volumetric.
Benefits and advantages
Reduction of water hardness, which is cause of scale.
Energy saving
The device prevents the formation of deposits in pipes and hydraulic lines. Greater sense of wellness during the shower. Skin soft and clean. Increased duration of appliances and boilers.
Cost saving
Reduction in the use of soaps, fabric softeners and chemicals. Reduced maintenance costs. Fully automatic operation. It should just worry about adding salt in the water softner.
Features
* Min. pressure : 1.38 bar (1.38 kg/cm2)
* Max. pressure : 8.27 bar (8.27 kg/cm2)
* Minimum temperature: 2°C
* Maximum temperature: 38°C
* Input / Output water 1″ female thread
* Exhaust: hose connector with 2m. of tube
* Overflow: hose connection 3/8″
Attention
The pressure tanks are supplied filled up to version 40lit.
Model Specifications
8lt. resin. (for 1/2 people)
– Exchange capacity: 44ºHFxm3
– Salt consumption for regeneration: 1.24 Kg. / Salt.
– Water consumption for regeneration: 53,6lt.
– Quantity of water treated for regeneration, 30°F-0,68m3, 35°F-1,26m3, 40°F-1,1m3, 45°F-0,98m3, 50°F-0,88m3, 60°F-0,73m3.
– Max. flow 0.32 m3/h
– Dimensions ØxH (mm.) 203×632
– Pressure vessel – 8lit.: 8″x17″
– Brine tank ØxH (mm.) 340×470 – capacity salt 30lit.
12lt. resin (for 2/3 persone)
– Exchange capacity: 66ºHFxm3.
– Salt consumption for regeneration: 1,8 Kg./salt.
– Water consumption for regeneration: 80,4lt.
– Quantity of treated water for regeneration, 30°F-2,2m3, 35°F-1,88m3, 40°F-1,65m3, 45°F-1,46m3, 50°F-1,32m3, 60°F-1,1m3.
– Max. flow: 0,54m3/h
– Dimensions ØxH (mm.) 178×959
– Pressure vessel – 12lit.: 7″x30″
– Brine tank ØxH (mm.) 340×470 – capacity salt 30lit.
15lt. resin (for 3/4 persone)
– Exchange capacity: 90ºHFxm3.
– Salt consumption for regeneration: 2,5 Kg./salt.
– Water consumption for regeneration: 100,5lt.
– Quantity of water treated for regeneration, 30°F-3,00m3, 35°F-2,57m3, 40°F-2,25m3, 45°F-2,00m3, 50°F-1,8m3, 60°F-1,5m3.
– Max. flow 0,68m3/h
– Dimensions ØxH (mm.) 196X1.087
– Pressure vessel – 15lit.: 7″x35″
– Brine tank ØxH (mm.) 340×905 – capacity salt 75lit.
20lt. resin (for 4/6 persone)
– Exchange capacity: 110ºHFxm3.
– Salt consumption for regeneration: 3,2 Kg./salt.
– Water consumption for regeneration: 134lt.
– Quantity of water treated for regeneration, 30°F-3,66m3, 35°F-3,14m3, 40°F-2,75m3, 45°F-2,44m3, 50°F-2,2m3, 60°F-1,83m3.
– Max. flow 0,942m3/h
– Dimensions ØxA (mm.) 203×1.087
– Pressure vessel – 20lit.: 8″x35″
– Brine tank ØxH (mm.) – 340×905 – capacity salt 75lit.
25lt. resin (for 6/8 persone)
– Exchange capacity: 137ºHFxm3.
– Salt consumption for regene ration: 3,9 Kg./salt.
– Water consumption for regeneration: 167,5lt.
– Quantity of water treated for regeneration, 30°F-4,56m3, 35°F-3,14m3, 40°F-3,91m3, 45°F-3,04m3, 50°F-2,74m3,
60°F-2,28m3.
– Max. flow 0,942m3/h
– Dimensions ØxH (mm.) 228×1.091
– Pressure vessel – 25lit.: 9″x35″
– Brine tank ØxH (mm.) – 340×905
– capacity salt 75lit.
30lt. resin ( for 6/8/10 persone)
– Exchange capacity: 160ºHFxm3.
-Salt consumption for regeneration: 4,3 Kg./salt.
– Water consumption for regeneration: 201lt.
– Quantity of water treated for regeneration, 30°F-5,33m3, 35°F-4,5m3, 40°F-4m3, 45°F-3,55m3, 50°F-3,2m3, 60°F-2,66m3.
– Max. flow 1,47m3/h
– Dimensions ØxH (mm.) 253×1.087
– Pressure vessel – 30lit.: 10″x35″
– Brine tank ØxH (mm.) – 340×905 – capacity salt 75lit.
35lt. resin
– Exchange capacity: 175ºHFxm3.
– Salt consumption for regeneration: 5,2 Kg./salt.
– Water consumption for regeneration: 210lt.
– Quantity of water treated for regeneration, 30°F-5,83m3, 35°F-5m3, 40°F-4,37m3, 45°F-3,88m3, 50°F-3,5m3, 60°F-2,91m3.
– Max. flow 1,56m3/h
– Dimensions ØxH (mm.) – 254×1.318
– Pressure vessel – 35lit.: 10″x44″
– Brine tank ØxH (mm.) 340×1.160 – capacity salt 100lit.
40lt. resin
– Exchange capacity: 200ºHFxm3.
– Salt consumption for regeneration: 5,9 Kg./salt.
– Water consumption for regeneration: 240lt.
– Quantity of water treated for regeneration, 30°F-6,66m3, 35°F-5,71m3, 40°F-5m3, 45°F-4,44m3, 50°F-4m3, 60°F-3,33m3.
– Max. flow 1,56m3/h
– Dimensions ØxH (mm.) 254×1.318
– Pressure vessel – 40lit.: 10″x44″
– Brine tank ØxH (mm.) 340×1.160 – capacity salt 100lit.
50lt. resin
– Exchange capacity: 250ºHFxm3.
– Salt consumption for regeneration: 7,3 Kg./salt.
– Water consumption for regeneration: 262lt.
– Quantity of water treated for regeneration, 30°F-6,66m3, 35°F-5,71m3, 40°F-5m3, 45°F-4,44m3, 50°F-4m3, 60°F-3,33m3.
– Max. flow 1,56m3/h
– Dimensions ØxH (mm.) – 254×1.575
– Pressure vessel – 50lit.: 10″x54″
– Brine tank ØxH (mm.) – 530×800 – capacity salt 150lit.
60lt. resin
– Exchange capacity: 300ºHFxm3.
– Salt consumption for regeneration: 9,1 Kg./salt.
-Water consumption for regeneration: 360lt.
– Quantity of water treated for regeneration, 30°F-10m3, 35°F-8,57m3, 40°F-7,5m3, 45°F-6,66m3, 50°F-6m3, 60°F-5m3.
– Max. flow 2,21m3/h
– Dimensions ØxH (mm.) – 254×1.722
– Pressure vessel – 60lit.: 12″x48″
– Brine tank ØxH (mm.) 530×800 – capacity salt 150lit.
70lt. resin
– Exchange capacity: 350ºHFxm3.
– Salt consumption for regeneration: 11,3 Kg./salt.
– Water consumption for regeneration: 511lt.
– Quantity of water treated for regeneration, 30°F-11,66m3, 35°F-10m3, 40°F-8,75m3, 45°F-7,77m3, 50°F-7m3, 60°F-5,83m3.
– Max. flow 2,63m3/h
– Dimensions ØxH (mm.) 330×1.580
– Pressure vessel – 70lit.: 13″x54″
– Brine tank ØxH (mm.) 530×800 – capacity salt 150lit.
75lt. resin
– Exchange capacity: 375ºHFxm3.
– Salt consumption for regeneration: 15 Kg./salt.
– Water consumption for regeneration: 538lt.
– Quantity of water treated for regeneration, 30°F-12,5m3, 35°F-10,71m3, 40°F-9,38m3, 45°F-8,33m3, 50°F-7,5m3,60°F-6,25m3.
– Max. flow 2,63m3/h
– Dimensions ØxH (mm.) -330×1.580
– Pressure vessel – 75lit.: 13″x54″
– Pressure vessel 530×800 – capacity salt 150lit.
80lt. resina.
– Exchange capacity: 400ºHFxm3.
– Salt consumption for regeneration: 15 Kg./salt.
– Water consumption for regeneration: 538lt.
– Quantity of water treated for regeneration, 30°F-13,33m3, 35°F-11,42m3, 40°F-10m3, 45°F-8,88m3, 50°F-8m3, 60°F-6,66m3.
– Max. flow 2,63m3/h
– Dimensions ØxH (mm.) – 254×1.575
– Pressure vessel – 80lit.: 13″x54″
– Brine tank ØxH (mm.) – 530×1.050 – capacity salt 200lit.
Included
– By-Pass valve
– chlorine generator
– three pieces housing 10″ in & out 1″
– 1 polypropylene filter 20 micron
– 1 titrant kit.
– 1 Chlorine generator
